f

Monday, December 19

How to Make Baby Joggers From a Tee Shirt



It finally got too cold for shorts here in Phoenix, so joggers were a natural progression. I love that they're stretchy and allow for plenty of running, crawling, and climbing.

Edison's hoodie in the photos above, if you're curious, is from A Quiver Full. Use the code "JESUS" for 20% off!

This project has been sitting on my Pinterest board for ages, and I finally did it! If my photos and directions below don't make sense, check out the original tutorial I followed here. These really do take half an hour, or less! I made two pairs during one nap-time.

You will need: 

  • An adult tee shirt. I used an old shirt from Loft. 
  • 1/2 wide elastic for the waistband.
  • Paper for your pattern. 
  • A sewing machine and thread, scissors, etc.



Step 1: Make your pattern. On a large piece of paper, mark the waistband of the pants, and then the crotch, and then the ends of the legs on your paper, and fill in the sides. Add an inch to the top, because this will be folded over to make your waistband. Add a half inch around the edge, for your seam. Your patter should look a little more square than the pair of pants you're tracing.


Step Two: Cut out your pieces.  Place your tee shirt on a flat surface, making sure the hem lines up. Then pin your pattern to the tee, lining up the legs with the bottom of the shirt (I didn't get the left leg lined up perfectly, but ideally, they should both line up). Then cut through both layers of the tee.


Step Three: Turn the pieces so the right sides are together. Then, sew a quarter inch seam around the pant legs.


Step 4: Fold over your waistband, and sew down the edge, leaving a gap of a couple inches for putting in the elastic.


Step Five: Going off of the existing pair of pants you used for your pattern, measure your elastic and cut it to that size. Push a safety pin through one end, and then feed it through the hole you left in the waistband, and pull all the way through. 


Once you have the elastic all the way through, you'll need to sew the ends of the elastic together. fold them over each other, and sew a few lines up and down to tack them together. Above, I've done it on a second pair of pants. Getting the elastic under the sewing machine is probably the most tricky part of this whole thing.


Step Six: Once the elastic is back inside, sew the gap closed, and turn right side out. 

Tada! Happy Christmas crafting! And enjoy some more photos of Edison modeling :)

Saturday, December 17

Life Lately: Simple Christmas



Friday, I left work a little early to try to do some cleaning at home before Brian got off work and picked up Edison from daycare. I turned up the Christmas worship music, and starting from the living room, began mopping my way to the other end of the house. It was slow work, since we haven't mopped for, oh, a few months? It's bad when you can't remember the last time you mopped.

But when I made it to Edison's room, as I flipped on the light, I felt that the light switch was all sticky. And I couldn't help but smile.

Sticky light switches make me think of our nightly bedtime routine. After Edison has his pajamas on and his teeth brushed, while I hold him up, he switches off the bathroom light, then the hallway light, and then his bedroom light last of all.

I never would have thought there'd be a day that sticky light switches made me happy. Or the puppies, trucks, books, and blocks I see scattered all over the living room floor from where I sit typing.

But when I see toys all over the floor, or touch a sticky light switch, I'm struck by that feeling. The one all mothers know, the feelings of overwhelming love, joy in this moment, fear that life is going by too fast, sadness of knowing how fleeting it is, sheer happiness in the present. All mingled and combined into the emotion that is motherhood.

So, I'm trying to take each day slowly. My house isn't decorated as much or as well as I'd like, like the photos I can't stop pinning on Pinterest, but Edison loves the Christmas tree (and especially the switch that turns the lights on and off) just as it is.

We haven't made any cute Christmas crafts. I probably won't have time to put together clever gifts for his teachers at daycare. I forgot to get the mailman anything. I've fallen behind on my Advent calendar and devotional, but the scripture and lessons for the days I have done has been a blessing. I might not get all the gifts for all the people I'd like, or send enough Christmas cards, or bake anything at all.

After all, people, I've just mopped my floor for the first time in ... a very long while, so that should tell you where to set your expectations.

We probably won't go do all the fun Christmas activities, or fit in all of the Christmas movies, or see all the people we'd like to see while we're in Iowa for Christmas. But I don't want this Christmas to go by wishing I'd done more, or seen more, or had more. I just want to be truly present in each moment.

I think that's the best gift I can give.

Monday, November 28

DIY Christmas Decor: Marble and Gold Letters


So, I told you marble contact paper was addicting. 

Last week was Thanksgiving, and despite the contentions and deep divides around us, I hope you had peace around your Thanksgiving dinner table, and you were able to be truly grateful for those with you and your many blessings.

I think "peace" is especially applicable this Christmas season. As Advent begins, the season of expectant waiting, it's a reminder that the Prince of Peace did come to this world as a baby, and live with us. He's the Healer, and ultimate King.

Also, I'm writing this post before Thanksgiving, and I may or may not be listening to Christmas music. Ok, I'm definitely listening to Christmas music. 

Have you seen the Christmas decorations at Target? I fell in love with the marble Christmas trees. Marble matches everything, and is so classy.

I took that marble idea, and expanded on it for these marble and gold letters!
You'll Need: 


Step 1: Fold your contact paper so that right sides are together, like it is in the image above. 


Step 2: Then trace and cut out your letters. You may need to use a craft knife to cut out some shapes, depending on what letters you choose. "JOY" would have been a bit easier!


Step 3: Peel and stick the contact paper letters to the cardboard letters. Smooth out any bubbles under the surface. This part is the most fun!


Step 4: Paint the edges of the letters gold. I'd tried to use my copper contact paper, but without success. Paint is much easier, and I love the finished result!





Now that Thanksgiving is over, it's now acceptable for me to take down my fall decorations and bust out the Christmas stuff. These will find a new home on my mantle. 


(And if you like that painting ... I made that too, and I can post a tutorial for that also. The premise behind it is so easy, anyone could do it.)

So bust out the Christmas music with no shame, and get to spreading that Christmas cheer! Peace on earth, good will to men!

Wednesday, November 23

DIY: Make A Faux Marble and Copper Mousepad




In the last post on our office, we were still using a kitchen table and black desk. Someday I'll have the finishing touches ready and I'll share the rest, but *spoiler alert* we now have white desks.

I can't tell you how much I love my desk, but the white surface did create an issue with my computer mouse. For weeks, I couldn't figure out why my computer would turn on, but the mouse wouldn't respond. Finally, I mentioned it to Brian, and in five minutes he diagnosed the issue - no mouse pad. He let me use his, which is covered with lovely photos of car parts and Motocraft products. But I wanted something a little more me.

I was inspired by the lovely marble mouse pads I found on Etsy for $20, and figured out how to create my own.



You'll need:



Step 1: Cut your craft foam to size. 


Step 2: Trace your craft foam onto your marble contact paper. We're going to add a section of copper, so mark how far you want the marble to come. Then cut it out.


Step 3: Slowly, peel and stick the contact paper to your foam, smoothing out any bubbles.


Step 4: Trace and cut out a section of copper contact paper to fit, and repeat - smoothing out any bubbles.


And that's really all there is too it!


Want other ideas for using your contact paper? You can trace your laptop and apply it to the back of the screen, use it to give an upgrade to a bland desk lamp, wrap your pencil holder, and add some pieces to your desk accessories, like your stapler or table dispenser. 


Soon, I'll post a Christmas decor idea using the marble contact paper. But I'd love to hear from you, have you used contact paper in crafts? What other ideas do you have for cool uses for it? Share them with us in the comments below!

Monday, November 21

DIY: How to Make a Tree Stump Stool for $50 or Less


Side tables: marriage-savers. 

Let me explain. As Edison grew more and more mobile, we quickly realized that we could no longer use the coffee table as a table, since now he could reach almost anything on it. Yes, I know, we shouldn't eat on the couch in front of the TV, but this is real life, and sometimes after we've both had long days at work, the best thing ever is to order a bunch of wings and fries, and settle in on the couch to watch the next episode of Last Man Standing, together, or now that it's fall, the next Harry Potter movie. Or we might just have leftovers and popcorn for dinner. Don't judge. 

Not being able to use the coffee table for food meant that we were down to one side table at one end of the couch: my end. That lead to some encroaching, and much annoyance on my part.

So to save our marriage, we needed a second side table. I'd wanted a tree stump side table forever, but they're not cheap. This one from West Elm is $249


So we made our own, for the total cost of about $50.


You'll need: 

  • A tree stump that's 6" shorter than your sofa arm. Look on Craig's List for free tree stumps! We found tons of options to choose from. I recommend pine; the bark comes very easily, and on some types of wood, like walnut, it can be really hard to remove. 
  • Wood stain (optional). I used Miniwax stain in "Natural."
  • Clear polyurethane gloss
  • An assortment of tools for removing the bark. 
  • A sander, or sandpaper blocks. 
  • Foam brushes. 
  • 6" Hairpin metal legs. I bought these ones from Amazon for $30, and they were the perfect height and look I wanted.
  • Wood shims, unless your log comes leveled already.  
  • A level, in case it doesn't.
  • Long screws. The screws that come with the legs may not be long enough.
  • An impact driver.

Step 1: After you've picked up your free tree stump from someone's woodpile, the next step is removing the bark. I'd assembled a variety of tools for the purpose, but the bark fell off so easily, I only ended up using the screw driver! It only took a couple minutes to scrape it clean.


Step 2: Sand the top and sides of the stump. Edison was a great helper during this step. Just kidding. He wasn't allowed near the sander while it was turned on. I, however, did do the sanding, and this is the closest I've ever been to using power tools. It was exhilarating!

You don't need to go crazy with sanding, but just make sure the surface feels smooth. Run a tack cloth over the surface to remove any dust before the next step.


Step 3: Stain the stump. This step is optional - if you like the wood's natural color, you can skip this. I wanted just a tad richer and more even color, so I used Miniwax stain in "Natural." Use a foam brush to apply it in a thin layer, and let it dry according to the instructions on the can, which is about 8 hours. Don't sand it after applying the stain; that will essentially undo everything you've just done. 


Step 5: The next day, apply an even coat of polyurethane in the same way. This has to dry overnight between coats. Now, if you find rough areas on the wood - sand these down between coats of polyurethane. You don't need to sand between coats like you would if you were using paint, the sanding is just to keep it smooth. 

I applied about three coats before I was satisfied with the finish on this stump.


Step 6: Attach the legs. This is the only moderately tricky part. Turn your stump upside down, and arrange the legs on the bottom. I used this set of four from Amazon, but fitting all four was going to be tricky. I was concerned that three might not be stable, but Brian explained that you only need three points to establish an infinite plane, or something to that effect (that's what happens when you ask an engineer). 


The tricky part about this is making them level. Because we got an already cut stump, and we didn't want to try to cut it again, because that would make it too short, we used wood shims to level out the bottom.

Hold the level from the end of each leg to the others to check the height, and add shims underneath as needed.


After each point is level, put in at least one screw to hold in the legs. You may need to use larger screws than the ones that come with the legs. Then turn the table over, and check to see if you succeeded.


Perfect!

But what about those unsightly pieces of wood sticking out? To clean it up, you'll have to flip it back over and trim them off, as Brian is demonstrating with the saw.


Then secure the legs with the rest of the screws.


Step 7: Carry it inside, and enjoy having a place to put your wings out of the reach of your toddler, and having your own spot on the couch back!


We did leave that long branch sticking out, as you can see above, for the only reason that it really helps make it easier to move. This thing is heavy! But at least we don't need to worry about Edison tipping it over.


I couldn't be happier with how it turned out! Now, I'm tempted to switch favorite spots on the couch with Brian ... if he's willing to trade.